contact force
英 [ˈkɒntækt fɔːs]
美 [ˈkɑːntækt fɔːrs]
接触压力
双语例句
- Reduced contact force due to temperature effect and control module tolerances.
由于温度效应和控制单元公差导致的接触力降低。 - Contact Force Simulation and Test Analysis of Docking Mechanism
对接机构方案样机轴向缓冲力仿真分析与试验验证 - The residual contact force, which is the important reason for the tight connection between the tube and sleeve, exists between the tube and sleeve.
成形后导管管套之间存在的残余接触力，是导管管套紧密连接在一起的重要原因； - However, I want you to appreciate the fact that the force from the surface onto this object is, of course, the vectorial sum between these two, and that is what's called normally the contact force.
但是，我希望你们，明白，物体承受来自，表面的力，是这两个，向量的合，这个我们通常，叫做触点压力。 - With luck, these variations may serve to provide a contact force greater than the designed value.
然而，很可能实际的触点压力同样要小于设计者的期望值。 - The end-of-life contact force will almost certainly be lower than the force generated by the first contact cycle.
末期触点压力几乎一定小于第一个循环产生的力。 - Side and bottom contact shoes are spring loaded to provide the necessary contact force.
边触式和下触式集电靴装有弹簧用来提供所需的接触压力。 - The contact method with low contact force on Al electrodes is required for test probing of LSI for the next generation.
下一代的大规模集成电路的测试探头要求使用在铝电极上的低接触力的联接方法。 - In order to maintain adequate end-of-life contact force, the contact must be designed to give an initial force greater than the minimum required for electrical signal integrity.
为了维持足够的末期触点压力，接触必须可以产生大于电信号整体性所需要的最小力的初始力。 - And that contact force better be exactly the same as mg, but in opposite direction, otherwise there could never be equilibrium.
触点压力和，mg完全，相同，但是反向相反，否则永远都不会有平衡。 - Permanent set is one method by which the contact force decreases over time.
永久变形是触点压力随着时间变化而降低的一种方式。 - Effect of Corrugation to Rail Shakedown and Wheel-rail Contact Force
波浪形磨耗对重载钢轨安定性及轮轨接触力的影响 - In any case, for the signal to pass through with minimal alteration, the contacts within the connector must maintain good contact force and resist corrosion over the life of the contact.
在任何情况下，对于需要传递而只允许最小限度变异的信号而言，连接器内的触点必须接触良好并能在接触期间抵抗腐蚀。 - Coincidence between the orientation of normal contact force anisotropy and the direction of the major principal stress has been observed during all stages of shear loading.
整个加荷过程中，剪切带内大主应力的偏转方向与法向接触力各向异性的主方向保持了良好的一致性。 - Stress relaxation is another phenomenon that results in loss of contact force.
应力松弛是导致触点压力损失的另一现象。 - In the mean time, the vertical and roll motions of the pantograph fame should be as small as possible, so that to make the contact force as normal as the conventional train.
并且使受电弓框架垂向位移和侧滚角度足够小，弓网接触压力达到车辆正常曲线通过时的水平。 - Therefore, the best material for the job will be the one that most effectively retains greatest percentage of the initial contact force over the life of the contact.
所以，适合该项目的最好的材料应是在接触末期可以最有效地保持最多的初始触点压力的材料。 - However, if the stress level is reduced, the contact force is reduced as well.
但是，如果应力水平降低，触点压力也随之降低。 - The system movement laws, contact force between rolling element and convex, concave sphere in the joint, friction torque and system actuating torque were obtained.
得到了系统运动规律，接头内滚动体与阴、阳球体间的接触力、摩擦力矩和系统作动力矩。 - Force compensation system comprised of springs and a proportional valve makes the contact force stable in grinding process.
弹簧、比例阀构成的力补偿系统保证了磨削过程中接触力的稳定。 - The design of the pantograph's active control system and the study of the simulation results reduce the fluctuation of the contact force theoretically and thus improve the current collecting quality.
通过受电弓主动控制系统的设计和对其的仿真研究，理论上降低了弓网系统接触压力的波动，从而改善了受流质量。 - According to calculating different speeds of curve negotiation and axle load, the wheel-rail contact force and contact stress field are obtained separately, and then compared with each other to offer theory basis for finding the method which can slow down rail wear.
针对不同的曲线通过速度和不同的轴重进行计算，得出了轮轨接触力和接触应力场，并对其进行了分析比较，为找到减缓钢轨磨耗的方法提供了理论依据。 - The variation of the tooth deformation and the mesh stiffness and the contact force and the contact stress of a pair of shearer gear in the mesh process have been studied.
研究一对齿轮在啮合过程中轮齿变形和应力、刚度和接触力变化。 - The distributing law of contact force and its variety law are obtained.
其次，对动力固结法进行了数值模拟分析，得出了锤底接触力的分布及变化规律。 - Study is conducted on contact searching algorithm and contact force algorithm.
研究了接触搜索算法和接触力算法。 - The analysis model of contact force between finger and object at equilibrium condition was discussed.
同时分析了静平衡状态下，手指与物体接触的作用力。 - The process to conduce the vertical nonlinear elastic Hertz contact force and the horizontal Kalker creepage theory is presented.
给出了垂向Hertz非线性弹性接触力和横向Kalker蠕滑理论的推导过程。 - The contact force and kinematic pair are added, and the complete virtual prototype mechanical model is established.
添加接触力和运动副，建立了馈源支撑系统完整的虚拟样机机械系统模型。 - The application of object impedance model with force tracking capability ensures the reliability of the contact force control.
应用具有力跟踪能力的目标阻抗模型，保证了接触力的稳定性。 - Completed the dexterous hand grasp simulation in ADAMS, obtained the contact force curve when stability grasp.
在ADAMS中完成了灵巧手的抓取仿真，得到了灵巧手稳定抓取时的接触力曲线。